How To Set Up A Sway Bar Hitch

Weight Distribution Hitch Setup

How to Set Up a Weight Distribution Hitch - CURT

Weight Distribution Hitch Setup

8 Piece of cake-to-Follow Steps!

Weight distribution hitch installation involves leveling the trailer, measuring vehicle and trailer height, mounting the hitch caput, shank, spring confined and hookup brackets, and adjusting the weight distribution hitch every bit needed.

In this guide, we will comprehend stride by step how to set up a weight distribution hitch. Each hitch is unique, and then make sure yous follow the instructions included with your particular model.

Weight Distribution Hitch Installation Video

How to Install and Suit Your Weight Distribution Hitch

Step one: Mensurate vehicle and trailer height

Park your vehicle and trailer on a level surface and use the trailer natural language jack and a level to make certain your trailer is parallel with the ground.

Measure and record the height of your vehicle and trailer. You will demand to know the altitude from the ground to the top of the trailer coupler and the distances from the footing to the bottom of the rear bumper and front bumper on your tow vehicle. You can likewise utilize the distance from the ground to wheel well if you prefer.

Footstep 2: Attach the WD shank and hitch head

Insert the weight distribution shank into the receiver tube. Be certain that the shank is fully inserted in the receiver tube of your trailer hitch and secure it using a hitch pin & clip.

Position the head assembly on the adjustable shank. The head should exist raised into position so that the superlative of the trailer ball is i to three inches in a higher place the coupler tiptop. Use ane mounting bolt at the bottom of the assembly to hold it in identify, but do not tighten with a nut.

Need more drib or ascension? Shop replacement shanks

Step 3: Ready weight distribution hitch head angle

Pivoting the head downwardly, place 2 washers on the adjustment rod and insert the rod into the lower hole on the head. Some weight distribution hitches may not require this pace, having a different adjustment machinery. Remember to consult the instructions specific to your weight distribution hitch.

Rotate the head up into the mounting position on the shank. Information technology should be vertical or tilted slightly dorsum. You lot may need to add together or remove washers to achieve the proper angle.

Finally, insert the second commodities into the tiptop hole in the hitch head and fasten both bolts with the provided nuts and washers. Tighten the bolts merely only enough to hold the head in place.

Step 4: Install spring confined and couple the trailer

Mountain the spring confined on the hitch head. If the spring bar chains have not yet been attached, attach them to the leap bars before mounting the bars to the head.

Raise the trailer coupler, and back the tow vehicle up to couple the trailer to the trailer ball.

Pace 5: Raise the trailer jack

With the coupler latched onto the trailer brawl, lift upwards the coupling betoken using the trailer jack. The coupler should exist raised nigh three inches above the level position.

Step 6: Engage the hookup brackets

Position the spring bar hookup brackets on the trailer frame using the spring bar bondage equally a guide. Mount the brackets onto the trailer frame using the provided bolts.

And then, attach the leap bar bondage to the brackets. Make certain both sides are spaced the same vertically, with number of chain links betwixt the spring bars and the hookup brackets. Then pry the brackets into the locked position using the provided elevator handle.

Note: At that place must exist a minimum of five chain links between the subclass and the leap bar.

Step 7: How to arrange weight distribution hitch

Retract the trailer jack so that the full weight of the trailer is resting on the hitch. And so, re-measure the distances betwixt the ground and the front and rear bumpers. Each distance should exist within ane/ii" of the original measurement. If the distances have inverse too drastically, you tin adjust the number of links on the jump bar chains to increment or decrease tension. You can also arrange the tilt of the head unit.

Step eight: Fully tighten the bolts

Uncouple the trailer and torque all hardware to the values specified in the instructions.

Weight distribution setup differs across various models. With your weight distribution hitch, always follow the instructions provided past the manufacturer, and remember to accept your time.

Weight distribution and sway command in one product!

The TruTrack™ weight distribution hitch features an innovative design that levels the vehicle-trailer combination, while actively keeping the trailer from swaying.

No need for a separate sway command unit!

Back to Weight Distribution Hitches